🍪 CompoundTalk uses cookies to improve your experience, analyze traffic, and personalize content. By continuing to use this site, you agree to our Cookie Policy.
Evidence-based GLP-1 & peptide discussion since 2023
ForumsCompounding & FormulationJust did my first reconstitution and I think I messed up — anyone have experience?

Just did my first reconstitution and I think I messed up — anyone have experience?

pete_manc_UK Tue, Nov 25, 2025 at 5:25 PM 6 replies 987 viewsPage 1 of 2
This thread is more than 6 months old. Information may be outdated. Consider searching for more recent discussions.
pete_manc_UK
Senior Member
1,234
5,678
Mar 2024
Manchester, UK
Nov 25, 2025 at 5:25 PM#1

I reconstituted a 10mg vial with 2ml of bacteriostatic water and I want someone to check my unit arithmetic before I draw anything, because I keep getting two different answers.

The three numbers to write on the vial: total mg, total ml, and mg per ml. Everything else is division. And the sanity check is that dose volume times number of doses should be less than the volume you put in, because dead space takes the difference.

The question I want answered is how to check the arithmetic without trusting a website calculator, since three calculators gave me three answers.

Practical detail welcome, however dull — the duller the better.

25 20TrialNerd_Beth, HPLC_Greg, LibrarianMeg and 22 others
Reply Quote Save Share Report
InsuranceTom
Senior Member
1,345
7,890
Mar 2024
Connecticut
Nov 25, 2025 at 6:44 PM#2

Answering the narrow version, because the broad one does not have a single answer. Do it in two steps and it stops being confusing. First concentration: 10mg into 2ml is 5mg/ml. Then volume: a 0.5mg dose is 0.5 ÷ 5 = 0.1ml. Then units, and this is where people go wrong — a U-100 syringe is graduated in hundredths of a millilitre, so 0.1ml is 10 units. The word "units" has nothing to do with milligrams; it is a volume marking that exists because insulin happens to come at 100 units per ml.

Happy to go further on any of that.

24 19lucas_SP_BR, lisa_labSD, adam_van and 21 others
Reply Quote Save Share Report
marco_milano
Member
345
1,456
Jul 2024
Milan, IT
Nov 25, 2025 at 8:03 PM#3
InsuranceTom said:
Do it in two steps and it stops being confusing.

InsuranceTom has the substance of this right. The condition it depends on is worth stating. The arithmetic is right and one caveat matters: a U-40 syringe changes the markings, not the volumes. If someone hands you U-40 and you read it as U-100 you will be 2.5 times out, and that error has a direction — it is always an overdose.

Ask again with the specifics and you will get a better answer than this one.

23 18Dr.LipidDallas, alex_tucson, kevin_tulsa and 20 others
Reply Quote Save Share Report

Sigma-Aldrich — Research-Grade Standards

Certified reference materials, analytical reagents, and research-grade standards for peptide verification. Trusted by laboratories worldwide.

Shop Reference Standards
DoseLogDan
Member
201
567
Feb 2025
Montana
Nov 25, 2025 at 9:22 PM#4
pete_manc_UK said:
I reconstituted a 10mg vial with 2ml of bacteriostatic water and I want someone to check my unit arithmetic before I draw anything, because I keep…

This matches mine closely enough to be worth saying so. Concentration choice is a precision decision, not a preference. Reconstitute high and every dose is a tiny volume where one unit of syringe error is a large fraction of the dose. Reconstitute low and you get more graduations per dose, so the same hand tremor costs proportionally less. Against that, more diluent means more benzyl alcohol and a shorter comfortable in-use window.

22 17sophie_paris, mel_PDX, Dr.AddMedPHL and 19 others
Reply Quote Save Share Report
Dr.AddMedPHL
Senior Member
1,234
6,234
Mar 2024
Philadelphia, PA
Nov 26, 2025 at 4:58 AM#5

Adding the clinical framing, because it changes how the question reads.

Regarding dosing arithmetic multi-dose vial contamination prevention: after reconstituting, I wipe the vial stopper with a fresh alcohol swab before EVERY single draw. I also never touch the stopper with my fingers and use a new needle for each draw.

Even with bacteriostatic water preservative, contamination is cumulative. One sloppy draw can introduce bacteria that multiply over days. Aseptic technique isn't optional — it's essential for injectable medications.

21 16JessicaM_2024, TomFromTexas, mike.trainer_LA and 18 others
Reply Quote Save Share Report

Similar Threads

503A vs 503B compounding — regulatory framework explained4 replies
Compounded semaglutide stability: accelerated degradation study results6 replies
Lyophilized vs liquid peptides — stability and bioavailability comparison18 replies
Bacteriostatic water sourcing and sterility considerations8 replies
State-by-state compounding pharmacy regulations — 2026 map8 replies
ForumsNewTrendingMembersAccount

Log In

Forgot password?
No account? Register